May 1, 2020

The user can set the number of instructions executed between updates to the simulator GUI by selecting a value from the Update Freq. menu. Certain update. Instructions are coloured blue, assembler directives (such as ORG, USING, etc) are As with many microcontroller simulators, EdSim51 allows the user to either . User Manual. James Kelly 3) Download om/ simulator/ the user may pause the program by clicking the button again.

Author: Dill Narr
Country: Indonesia
Language: English (Spanish)
Genre: Marketing
Published (Last): 10 September 2010
Pages: 324
PDF File Size: 5.22 Mb
ePub File Size: 9.26 Mb
ISBN: 367-2-46954-805-1
Downloads: 87291
Price: Free* [*Free Regsitration Required]
Uploader: Akisho

Below is a list of its features:. Standard – in standard mode the keys are independent of each other. The WR line connected to P3.

The 3 columns are connected to the inputs of an AND gate, the output of which is connected to P3. When running a program, the rate at which the screen updates is determined by the setting in the Update Guied. To switch between data memory and code memory the user clicks on the button that is labelled Data Memory when data memory is displayed and Code Memory when code memory is edslm51.

Also notice the background is grey. The data in this window can be cleared at any time by clicking the Rx Reset button. The programmer can write code directly here, or can load a program from file using the Load button dealt with in the next section.

Once the mouse button is released the key reopens. The keys can also be set to simulate switch bouncing – more info. The default Baud rate is The next instruction to uwer executed, its address is highlighted.

Now, a set of 8-bit numbers written in HEX can be transmitted.

As can be seen in the logic diagram above, the module is interfaced with the in 4-bit mode. Pulse – in pulse mode a key is closed while the left mouse button is held down.

  FPN - 07PG PDF

For details on how to communicate with the module, see HD In the image on the left, the motor’s shaft is in the default position pointing at 3 o’clock. Therefore, the next time the user opens a file dialog box by clicking on either the Load or Save buttons, the dialog box automatically opens in the last directory visited.

Data can then be written to gkide DAC. Notice the sensor depicted by guidr vertical line at the top of the motor is black.

Change the System Clock Frequency. As can be seen in the diagram below, the LED bank, the DAC inputs and the 7-segment display data lines all share port 1. Hex values can be entered by appending H after the number, or placing 0x before it. Again, like data memory, the address specified in the blue addr box can be altered by entering a value in the value box. If the file does not exist or is corrupted in some way, it is ignored and the simulator is launched with the original settings.

Data received from the ‘s serial port appears in the Rx window. This is not altogether true. The first bytes of code memory are displayed.

Edsim51 Examples

These settings are saved in a file called edsim51Settings. A screenshot of the microcontroller panel. Because it reads the high nibble first, the Function set high nibble must be sent again, followed by the low nibble.

These images shows what is connected to each of the 32 port pins. The keys in the keypad only bounce if the keypad mode is set to Standard. If the file exists then the information in it is used to restore the system settings to the values they were at when the simulator was last shut down.

If an error in the code is discovered, a message is displayed in the message box above the assembly code with a red background and the line with the error is highlighted within the code in red.


When text is transmitted, it is terminated by 0DH. Each character is made up of eight rows, with five dots in each row. There are two file types handled.

Until now the keypad could only be implemented using busy-waiting. F5H must be written as 0F5H. Also notice there is only one instruction for writing to the module. When stepping through the code, the instruction that was just executed is shown in the grey box at the top, together with the instruction’s address example shown: A closed key is reopened simply by clicking on it again.

But remember, you won’t be able to multiplex the displays and use keypad interrupts at the same time. Therefore, when exercising the motor, garbage messages may appear in the UART’s receiver window.

Edsim51 Examples | Micro controller (IE)

Copyright c James Rogers. When the simulator is launched it tries to open this file. Data can be transmitted to the ‘s serial port by typing text in the Tx window and clicking on the Tx Send button, which initiates transmission. An example for port 2 is shown below. When a switch is open a logic 1 appears on the port pin via the pull-up resistor while closing the switch connects the pin directly to ground – logic 0. The example on page 42 is for a 1-line display, but it nonetheless explains clearly how to initialise and communicate with the module in 4-bit mode.